Comprehensive Model Context Protocol server for managing Home Assistant through AI assistants.
Nothing to run from here
NestingCalc Calculators is installed from its publisher's own source and answers where it runs, so this marketplace is not in the path of a single call. There is no address here to send one to, and a panel that pretended otherwise would be showing you an answer we made up. Install it and call it from your own client — the Installation tab has the entry for each one.
37
tools declared
—
trust score
remote
at its publisher
—
calls last 7d
What it does
37 cutting and woodworking calculators: cut lists, sheet nesting, timber volume, kiln drying
Quickstart
# 1 — add it to Claude Code
claude mcp add --scope user --transport http nestingcalc-calculators-mcp https://mcp.nestingcalc.com/mcp
# 2 — ask your agent for something these tools do
# linear_cutting_optimizer, sheet_cutting_optimizer, board_feet_calculator and 34 more
NestingCalc Calculators costs nothing on mcprush: there is no plan to choose here, no cap to set and nothing mcprush can bill you for.
Publishernot claimed
NEAll 1 server
nestingcalc1 server
1 category
Collected from a public index. Nobody has claimed this account, so nothing here was written by its author — claim it if it is yours.
Installation
Where are you running it?
Every route below installs the same thing and ends at the same approval screen. Nothing here runs on your machine and nothing runs on ours: this server answers at its publisher’s own address, and what you install is the connection straight to it.
Claude Codedeclared by this listing
This is a public server: it answers at its publisher’s own address and this marketplace is not in the path. Claude Code registers it in one command; --scope user makes it available in every project. The transport below is http, as the publisher's own manifest declares it.
claude mcp add --scope user --transport http nestingcalc-calculators-mcp https://mcp.nestingcalc.com/mcpReconnect, or start a new session, and the tools appear in the model’s tool list.
Free on mcprush, and it answers at its publisher’s own address: this marketplace is not in the path, so there is no key of ours to hold and no card to add.
What it writes
One config entry pointing straight at the publisher’s own address — this marketplace is not in the path, and nothing from this listing executes on your machine.
What you approve
37 tools, with what each one reads, writes and reaches shown before you agree — the same list on every route above. Read the tool surface.
Tool surface
What the model actually sees. Descriptions are diffed on every release — see version history.
Optimize 1D cutting plans for bars, pipes and profiles (linear cutting stock problem, best-fit decreasing heuristic). Returns bars used, per-bar cut lists with positions, total waste and unplaced parts. A web_url with the plan prefilled is included for a visual SVG diagram.
No parameter schema on file.
Optimize 2D guillotine cutting plans for plywood, MDF, glass, sheet metal (2D nesting with kerf, per-part rotation lock for grain direction, optional sheet trim and multiple stock sizes). Returns sheets used, piece positions, utilization, estimated cut length/count and unplaced pieces. Includes a web_url with the plan prefilled for a visual layout diagram.
No parameter schema on file.
Calculate board feet and lumber cost (thickness x width x length / 144 in inches). Accepts multiple boards and an optional price quoted per board foot or per MBF (thousand board feet).
No parameter schema on file.
Miter angles three ways: corner mode (any corner angle between two pieces), sides mode (regular polygon with N sides), crown mode (miter + bevel for crown molding at a spring angle).
No parameter schema on file.
Weight of lumber by species, dimensions, quantity and moisture (dry/fresh), using species density tables. Optional custom density in kg/m3.
No parameter schema on file.
Rebar weight takeoff (d2/162 rule): total length, weight in kg and bars per tonne for a list of rebar lines. Supports metric mm bars and US # sizes as diameters.
No parameter schema on file.
Weight of metal stock per profile: pipe/tube (OD + wall), round bar, square/rectangular tube, flat bar, angle, beam/I-beam. Materials: steel, stainless, aluminum, copper, brass.
No parameter schema on file.
CNC spindle RPM and feed rate from tool diameter, flute count, chip load and cutting speed. Works for routers and mills, metric and imperial.
No parameter schema on file.
Convert sheet metal gauge to thickness (mm) or thickness to gauge, and compute sheet weight for steel, stainless, aluminum or galvanized steel.
No parameter schema on file.
Tiles, boxes and cost for a room: room and tile dimensions, grout width, waste factor by layout pattern (straight, offset, diagonal, herringbone...), optional box size and prices.
No parameter schema on file.
Wallpaper rolls needed for a wall, accounting for pattern repeat and openings. Use a standard roll preset (eu, us-single, us-double, commercial54) or custom roll dimensions.
No parameter schema on file.
Equal baluster/spindle spacing for a run: number of balusters, exact gap and positions. Enforces a maximum gap (e.g. the 4-inch / 100 mm sphere code rule).
No parameter schema on file.
Laminate/vinyl plank takeoff: planks, boxes and cost with offcut reuse between rows (best-fit), expansion gap, layout waste presets and direction.
No parameter schema on file.
Resize an embroidery design file (PES or DST) by a scale percentage. Returns stitch stats before/after, a density safety verdict (safe within +/-15%) and the resized file as base64.
No parameter schema on file.
Hoppus (quarter-girth) volume of round logs from mid-length circumference and length: (C/4)^2 x L. Returns Hoppus volume, true volume (x 4/pi), Hoppus tons (50 h ft3) and a board-feet approximation, with optional quantity and value per Hoppus unit.
No parameter schema on file.
Cubic volume of a log by classical formula: Huber (mid diameter only), Smalian (both end diameters) or Newton (all three, most accurate). Metric (cm, m) or imperial (in, ft); returns volume in m3 and ft3.
No parameter schema on file.
Japanese Agricultural Standard (JAS) log scale: official diameter rounding (floor to 1 cm below 14 cm, even 2 cm at 14 cm and above), oval-log averaging, optional +2 cm ovality adjustment and the length allowance for logs over 6 m. Volume per log and totals in m3.
No parameter schema on file.
Convert timber quantities between m3, ft3, board feet, MBF, Hoppus ft3, Hoppus m3 and Hoppus tons, and translate a price quoted in any unit into $/m3 and $/MBF (1 MBF = 2.3597 m3).
No parameter schema on file.
Weight of a roundwood/log batch at any moisture content: W = volume x basic density x (1 + MC/100), per USDA Wood Handbook 2021 Ch.4. Presets for 14 verified species (acacia, rubberwood, eucalyptus, oak, teak, spruce...) or a custom basic density. Returns oven-dry mass, water mass and tonnes.
No parameter schema on file.
Stowage factor SF = cargo volume (m3) / cargo mass (tonnes), with classification against the IMO CSS Code Table 4.1 reference ranges for wood cargoes (sawn timber, tropical logs, plywood...).
No parameter schema on file.
How many uniform cartons fit in a shipping container before cube-out or weigh-out. Presets: 20GP (33.2 CBM nominal, 28,200 kg payload), 40GP (67.7 CBM, 26,700 kg), 40HC (76.4 CBM, 68 usable, 26,500 kg) — all editable. Returns max pieces by volume vs weight, the binding limit, balanced density (kg/m3) and containers needed for a planned quantity.
No parameter schema on file.
Sawmill recovery rate (lumber recovery factor): sawn volume out / roundwood volume in, benchmarked against FAO/EU/SE-Asia reference ranges. Also computes log-rule overrun/underrun: (actual BF - rule BF) / rule BF — Doyle underestimates small logs, so overrun is usually positive.
No parameter schema on file.
Wood moisture content (WH-2021 Ch.4 Eq. 4-1..4-4). Two modes: (1) sample-based MC_od/MC_wb from wet+dry masses; (2) drying outcome — mass + water lost when going from start MC to target MC. Optional Gb (kg/m³) returns MCmax and MCsink. Basis 'od' (oven-dry, industry default) or 'wb' (wet).
No parameter schema on file.
Wood shrinkage from a start MC to an end MC (WH-2021 Eq. 4-9: S_x = S_od × (1 − x/FSP)). Direction: tangential (board width) or radial (board thickness) or volumetric. Picks a species from the wood-species table (16 verified species) or accepts custom S_od + FSP. MC is clamped to FSP — above FSP wood doesn't change dimension.
No parameter schema on file.
Equilibrium moisture content (EMC) from temperature and RH using the Hailwood–Horrobin sorption model (Simpson 1973 coefficients, desorption branch — WH-2021 Ch.4 Table 4-2). Optional reverse mode: target MC → required RH at the given temperature.
No parameter schema on file.
Kiln charge capacity: wood volume per batch (AH-188 / TechDrying). V_wood = D×R×C × t/(t+s) × f where t=board thickness, s=sticker thickness, f=fill factor (0.85–0.95). Returns wood volume in m³ and board feet (1 m³ = 423.77 BF).
No parameter schema on file.
Rough sizing — convert between finished (planed, kiln-dried) and rough-sawn dimensions before drying and planing. Adds planing allowance (default 2.5 mm/face) + saw kerf (default 2.2 mm band) and applies WH-2021 Eq. 4-9 shrinkage. Direction: tangential (board width) or radial (board thickness).
No parameter schema on file.
Convert firewood volume between cord (128 ft3), stere/Raummeter (stacked m3), solid m3 (Festmeter), loose m3 and ft3, with optional weight estimate by wood species (dry/fresh).
No parameter schema on file.
Spindle speed (RPM) from cutting speed: n = Vc*1000/(pi*D) metric, n = Vc*12/(pi*D) imperial. Metric takes diameter in mm and Vc in m/min; imperial takes diameter in inches and Vc in SFM. Includes a web_url with the calculation prefilled.
No parameter schema on file.
Cutting speed from spindle speed: Vc = pi*D*n/1000 metric (m/min), SFM = pi*D*n/12 imperial. Always also returns the same speed converted to the other unit system. Includes a web_url with the calculation prefilled.
No parameter schema on file.
Allowable load on a simply supported rectangular timber beam (planning estimate, Eurocode 5 conventions, EN 338 grades C16-D40/D24-D40). Returns allowable UDL and center point load (gross and net of self-weight), governing mode (bending vs deflection at L/300), utilization, section properties. NOT a structural design - verify with an engineer. Includes a web_url with the beam prefilled.
No parameter schema on file.
Cut-to-size glass cost and weight estimate: net area with optional waste allowance, weight (2.5 kg/m2 per mm of thickness), material cost from your price per m2, optional polished-edge work per running metre, total and per-piece cost. Includes a web_url with the quote prefilled.
No parameter schema on file.
Cumulative yield through a wood production chain (sawing -> drying -> machining -> finishing). Multiplies stage yields, shows per-stage loss and computes the roundwood volume needed for a target finished volume.
No parameter schema on file.
Wood adhesive quantity: bond area x spread (g/m2, TDS presets like PVAc D3 175, EGP 250, finger-joint PUR 530) x application faces x waste allowance. Also computes bond area for edge-glued panels (joints from board width) and face lamination lay-ups.
No parameter schema on file.
Wood finishing paint quantity. Technical route: theoretical coverage = 10 x %volume solids / DFT(um), multiplied by transfer efficiency (conventional spray 30-35%, airless ~50%, HVLP ~65-90%, brush/roller ~90%); or a data-sheet coverage in m2/L. Adds an optional extra % for carved/3D surfaces.
No parameter schema on file.
Packing CBM for cartons: per-line and lot volume (m3), total weight and lot density, with a cube-out / weigh-out verdict against the 40HC balanced density (390 kg/m3 - same presets as container loading).
No parameter schema on file.
Bill-of-materials cost roll-up for furniture: buy quantity = net qty x (1 + waste%, verified presets: S4S lumber 18%, rough 28%, nested panels 10%, hardware 3%), line and total costs, cost per product and a selling price from a target margin (price = cost / (1 - margin)).
No parameter schema on file.
Free
$0 forever
- Every tool — any call limit is its publisher’s, not ours
- No card, and mcprush charges nothing for it
- Runs at its publisher’s own address — this marketplace is not in the path
- Nothing to cap, because mcprush bills nothing
What counts against your monthly calls
| Tool | Unit | Calls used | Out of the allowance |
|---|
Nothing here is billable: mcprush charges nothing to install NestingCalc Calculators or to call it, at any volume.
Call allowance · this installenforced at the gateway
Monthly allowance, in calls
—
—
Alert at 80% · then the tool returns a normal MCP error
Used this month: —
—Grade not published
No rule-by-rule report on file for this release
Two independent axes, because powerful and malicious are different questions. The grade is threat only. The capability level is blast radius, and it is never a penalty on the grade — it is priced as one subtract-only term in the score, where you can see it.
This listing is an address its publisher runs, and you connect to it directly — this marketplace is not in the path. The scanner reads packages and public source, and an address is neither. So there is no grade — not a withheld one, an unmeasured one.
Release history
This is an address its publisher runs: which release it serves is theirs to choose, so there is nothing here to pin. The history below is for reading; the current release on file is 1.2.0.
1.2.0
undated
latestNo release note was published with this version.
—
no reviews yet
Who can review
One review per account, from a signed-in account that does not publish this listing. Nothing else is asked — you can say what you think before you install it. Publishers can reply once per review, and a review can be edited or deleted by whoever wrote it.
Sign in to write one
Any signed-in account that does not publish NestingCalc Calculators can review it, once — before installing it or after. A review from an account that has installed it is marked as one.
No reviews yet
Nobody has reviewed this listing. The rating on the card is the mean of the reviews written here and nothing else, so there is no rating until somebody writes the first — which takes a signed-in account that does not publish it, and nothing else.